New Page 0

Convert Old Analogue Instruments and Sensors to NMEA 2000 Specifications
Display Engine and Fuel Data Plus more

Fully configurable screens with a true client-server architecture The Albatross On Board Client allows you to configure your own data screens, layout, type of indicators, units, alarms. It also supports multiple clients, connected with the Alba-CPU through Ethernet or Wi-Fi, so you can take your control bridge with you anywhere in the boat.
Engine monitoring	Energy resources	Resource levels
Remote control	Current alarms	Data log
The installation of the sensors Albatross interfaces connect your NMEA 2000 display or Alba-CPU to the devices you want to monitor, no matter you need to control fuel tanks, the RPM of the engines of the state of the bilge. To read all that measurements the Albatross interfaces use analog sensors . Albatross includes in its portfolio a large variety of sensors (temperature, pressure, level, etc…)
Fuel flow sensors	Tridata (speed/temp/depth)	Pressure sensors
Bilge level sensor	Waste water installation	Digital bridge with E-Series screens
Control panel	Engine	Propeller bow temperature sensor

NMEA Sensors, Adapters, Cables, Displays, Software
	Airmar Weather station PB200 Ultrasonic weather station with no moving parts. In addition to weather sensor it has inbuilt GPS receiver and heading compass sensor. Air pressure, wind, temperature, barometric pressure ... For land based weather stations. NMEA2000
	Albatross 4-Output Relay interface Alba-Out4 controls up to 4 switches by translating the information in the NMEA 2000 network into ON/OFF commands.
	Albatross 8-Output Relay interface Alba-Out8 controls up to 8 switches by translating the information in the NMEA 2000 network into ON/OFF commands.
	Albatross Alternate Current interface Alba-AC monitors voltage, current and frequency of the shore power, generator and inverter by translating the measurements into the NMEA 2000 communication protocol.
	Albatross Battery interface Albatross Control System can monitor with digital precision the following parameters according with the module or sensors : * Battery current * Battery temperature * Battery voltage
	Albatross Bilge interface Alba-Bilge monitors voltage input of the pump and liquid level detection input with ON/OFF or resistive sensor for 2 bilges by translating the measurements into the NMEA 2000 communication protocol.
	Albatross Engine interface unit A Complete and universal on board engine monitoring solution. Albatross Control System can monitor with digital precision the following parameters of any petrol or diesel marine engine: * Engine RPM, Alternator voltage, Oil pressure, Boost Pressure, Water Temp, Oil Temp
	Albatross Lighting interface Alba-Lighting monitors navigation lights (stern light, port, starboard), anchor light and motor navigation light by translating the measurements into the NMEA2000 communication protocol.
	Albatross Multipurpose interface Alba-Multi monitors 4 independent inputs for levels, pressures and temperatures with resistive sensors by translating the measurements into the NMEA 2000 communication protocol.
	Albatross Propeller interface Alba-Propeller monitors: • propeller speed and direction of rotation • exhaust and stern tube temperature
	Albatross Relay Input interface Alba-In monitors up to 8 ON/OFF inputs or switches by translating the measurements into the NMEA 2000 communication protocol.
	Albatross Tank Level interface Alba-Volume 3 monitors the volume of up to 3 tanks with pressure sensors by translating the measurements into the NMEA 2000 communication protocol.
	G2183 GPS Sensor Dual protocol GPS receiver. Supports both NMEA0183 and NMEA2000 simultaneously.
	GH2183 GPS / Heading Sensor The GH2183 eliminates the need to install a GPS antenna above deck and an electronic compass below deck. Supports both NMEA0183 and NMEA2000 simultaneously.
	H2183 Heading Sensor The solid-state three-axis compass with both NMEA0183 output and NMEA2000 bus. High accuracy even rough seas due three-axis rate gyro and accelerometer.
	Smart Transducer Airmar P39 DST (NMEA2000) The market leading depth sounding transducer. Unique digital signal processing algorithm can detect echoes down to an amazing 0.3 metres (1 foot). Unrivalled SNR with all-in-one housing give unsurpassed performance. Generates marine standard NMEA2000
	Smart Transducer Airmar P79 (NMEA2000) The market leading in-hull depth sounding transducer. Unique digital signal processing algorithm can detect echoes down to an amazing 0.3 metres (1 foot). Unrivalled SNR with all-in-one housing give unsurpassed performance. Generates marine standard NMEA2000
	NMEA 2000 Double Ended Cord Sets - SIzes from 0.5metres to 10 metres Double-ended cordsets are used for trunk or drop lines and make for a secure connection and simple timesaving installation. The connectors are keyed for error-free connection and are waterproof for continued operation even while submerged in the bilge
	NMEA 2000 Male and Female Field Attachable Connectors Field attachable connectors allow you to make field connections to bulk cable. The color-coded screw terminals match the individual wire colors found within in the bulk cable for error free field installation. Color-coded screw terminals make for error-free field installation. Rugged housing material designed to withstand harsh marine environments.
	NMEA 2000 Micro Inline Termination Resistor Termination Resistors are required on a NMEA 2000® network and are placed at each end of a network trunk cable. Like the double ended cord-sets, the termination resistors are waterproof and continue to function even while submerged in the bilge. Screw terminal connector for positive connections Termination resistors are used to terminate both ends of the trunk line The perfect part for use with a Airmar Weather Station mounted at the top of a mast or other distant location.
	NMEA 2000 Micro Power Tee A Powertap Tee is connected to a network backbone just like any Tee but rather than connecting a device their purpose is to provide “bus” power. NMEA 2000 Powertap Tee uniquely provides two power inputs permitting doubled power provision for devices.
	NMEA 2000 Micro Tee Drop A Tee is used to tap into the trunk line for adding a drop connection. The standard tee is also available with a cap for a protected diagnostic connection. Tees can be mated with all other devices on the network of the same connector style.

Airmar Weather station PB200

G2183 GPS Sensor

GH2183 GPS / Heading Sensor

H2183 Heading Sensor

Smart Transducer Airmar P39 DST (NMEA2000)

Smart Transducer Airmar P79 (NMEA2000)